Connecting to peripherals

What’s in the box?

  • Teamline 5141 room system
  • Teamline Touch touchscreen controller
  • Wall mounting kit
  • Cables
    • Ethernet cable
    • Two HDMI to HDMI cables (1.8 meters/5.9 feet)
    • Patch cable (2 meters/6.6 feet)
    • USB A to mini B (2.5 meters/8.2 feet)
  • StarLeaf microphone
  • A camera and where applicable, camera cables, mounting kit, and camera power supply

At this time, you must supply a C5 cloverleaf cord to connect the Teamline system to the mains power.

Positioning the Teamline 5141 system

  1. Choose an appropriate installation site:
    • The system must be accessible to ensure all cables are easily connected
    • Provide ventilation for the system; leave a space of at least 10cm (4 inches) behind, in front, and to the left and right of the system
    • Use a grounded AC power outlet for the system
  2. Wall mount the system or place on a firm horizontal surface. For information, refer to Mounting the Teamline 5141 system.

Connecting network cables

Using an Ethernet cable, connect the Network port on the rear of the system to an Ethernet switch in your network. The Ethernet port is a 10/100/1000 Mbit/s auto-sensing port and is set to ‘auto’ by default.

If your network doesn’t support automatic detection, you can configure the network speed manually. On the touchscreen controller that you have connected to the system, go to settings > networking > network port speed and select 100Mb/s (full).

Connecting the Teamline Touch

Using an Ethernet cable, connect the PoE Network port on the rear of the touchscreen to an Ethernet switch in your network. The Ethernet port is a 10/100/1000 Mbit/s auto-sensing port and is set to ‘auto’ by default. The touchscreen needs a switch/port that supplies PoE to function. For information about configuring the Touch, see Configuring Teamline 5141.

The speed and duplex settings at either end of the connection must be identical. Using non-matching settings causes severe packet loss.

Connecting the camera and microphone

To connect the camera and microphone:

  1. Connect the camera to either the USB 3.0 or USB 2.0 connector on the Teamline system.
  2. Connect one or two StarLeaf microphones to the USB connector(s).

For more information about microphones, see Microphone selection, placement, and setup.

If you have a dual display system, it is recommended that the camera is mounted on the display that contains the view of the main video. For more information about cameras, see Using cameras with Teamline 5141.

If you are using the Logitech Meetup camera, ensure you are running the latest version of the camera firmware. Otherwise, camera PTZ controls may not work properly on the touchscreen. For more information and to download firmware, go to the downloads area on the Logitech support site here: .

Connecting displays and audio

The audio emits from the left HDMI connector on the rear of the Teamline system only. If you are using one display, connect the supplied HDMI cable from the display to the connector on the left (closest to the power connector) on the Teamline system. For a two display system, connect the second display to the HDMI connector on the right. This second display will not emit audio.

Extending cables

For information about supported cable extenders and cable information, see Cable recommendations for room systems.

Connecting Pronto

If it has been included with your system, Pronto can be connected to devices (such as laptops) to share content and audio, and display current meetings on the Touch and room display, even if the room is not invited to the meeting. When connected to the device, Pronto detects active meetings in the user’s Outlook calendar, then enables the Join now tile on the Touch to allow users in the room to join the meeting.

Connect Pronto to the USB connector on the Teamline system using the USB-A cable, and ensure the other end of the cable is accessible to users to plug into their laptops. The first time users plug Pronto in, instructions are shown on the room display:

Image showing instructions on how to connect with Pronto

When the Pronto app is launched, the presentation source screen is shared to the room on the display and active meetings are displayed as a Join now tile on the Touch and on the room display. Future meetings in the user’s Outlook calendar that start within the next 15 minutes are displayed on the Touch and are visible on the room display. On subsequent connections using Pronto, the app does not need to be launched and content and meetings are shared immediately with the room.

Mounting Pronto

The supplied bracket can be used to mount Pronto to a surface using screws, ties (such as cable ties or Velcro), or adhesive mounting pads. Remove Pronto from the bracket to access the screw holes and slots for ties:

Connecting power

Connect the supplied DC +19V power connector to the rear of the system, then connect a C5 cloverleaf cord to the mains power.

Was this information helpful?